- You cannot add "ESP-WROOM-32 ESP 32S WIFI Bluetooth Development Board (CP2102 + 38PIN + Micro)" to the cart because the product is out of stock.
Official Texas Instruments TMDSDOCK28335 – Development Boards & Kits – TMS320 TMS320F28335 Experimenter Kit
- TMDSCNCD28335: TMS320F28335 DIMM100 based controlCARD
- DIMM100 Docking Station baseboard with DIMM100 controlCARD female connector
- XDS100v1 USB-to-JTAG Debug Probe enables real-time in-system programming and debugging
- Header pin access to key MCU signals – including most major digital IO and analog inputs
- Breadboard area for customizable routing/prototyping
- Board power can be provided by the provided USB cable or a 5V barrel supply
- Hardware Files are in C2000Ware at boards\controlCARDs\TMDSCNCD28335
Official 7Semi NEO-M9N GPS Breakout, Precision GNSS Positioning
-
High-precision multi-GNSS GPS breakout module
-
Supports GPS, GLONASS, Galileo, and BeiDou
-
Fast position update rate up to 25 Hz
-
3.3V operating voltage
-
I2C and UART communication interfaces
-
Low power consumption for battery-powered projects
-
Compact design for space-constrained applications
-
Ideal for drones, robotics, navigation, and IoT tracking
0.96 Inch SPI 7-Pin OLED Display Module with CS Pin (BLUE)
- Size: 0.96 inch
- Resolution: 128 x 64
- Controlling Driver Chip: SSD1306
- Display Area: 21.74 x 10.86mm
- Driving Voltage: 3.3-5V
- Operating Temperature: -40~70 Celsius
- Interface Type: SPI
- Light Color: BLUE
- Number of pins: 7
GY-302 BH1750 Light Intensity Module
- High precision determination accurate to 1 Lu for different lights
- Operating Voltage: 3-5VDC
- Built-in 16bit A/D converter
- I2C interface
INA240 Current Detection Amplifier Current Voltage Monitoring Bidirectional Module
- Wide -4V to 80V common-mode range
- Enhanced PWM suppression
- 200V/V fixed gain
- Analog voltage output
- Ideal for motor & solenoid control
LM393 Test Motor Speed Counter Sensor Groove Coupler Encoder Module
- Using imported groove optical coupling sensor, width 5mm.
- It has the output state light, if output high level, the lights are off. if output low level, it on.
- If it covered, it will output high level; otherwise, its output low level.
- Good signal and waveform, with a strong driving ability for more than 15mA.
- Equipped with a fixed bolt hole, easy install.
- Use the LM393 wide voltage comparer.
AM312 Mini Infrared Human Motion Sensor
- Operating voltage: DC 2.7-12V;
- Static power consumption: <0.1mA;
- Delay time: 2 seconds;
- Block time: 2 seconds;
- Trigger mode: repeatable;
- Sensing range: ≤ 100 degrees cone angle, 3-5 meters; (according to the specific lens)
- Working temperature: -20 – + 60 ℃
- Module lens: a small lens
TTGO T-Call V1.4 ESP32 Wireless Module SIM Antenna SIMCard SIM800H Module CH9102F Chip
-
ESP32 dual-core processor with Wi-Fi + Bluetooth support
-
SIM800H GSM/GPRS module for voice, SMS, and mobile data
-
Built-in SIM card slot with external antenna for strong signal reception
-
CH9102F USB-to-serial chip for fast & stable programming/debugging
-
Multiple GPIOs for sensors, actuators, and IoT peripherals
-
Compatible with Arduino IDE, ESP-IDF & MicroPython
-
Low-power design, ideal for IoT & remote monitoring applications
-
Perfect for GPS tracking, smart agriculture, automation, and IoT projects
Official NUCLEO-C092RC Development Board, STM32 Nucleo-64, STM32C092RC MCU Eval Board
- External SMPS to generate Vcore logic supply
- 24 MHz or 48 MHz HSE
- External SMPS experimentation dedicated connector
- Micro-B or Mini-B USB connector for the ST-LINK
- MIPI® debug connector
Texas Instruments LAUNCHXL2-RM46 Hercules RM46x/RM46L852 LaunchPad Development Kit
- Microcontroller: RM46L852
- USB powered and capability for external 5v supply
- On board USB XDS110 debug
- On board SCI to PC serial communication
- User programmable push buttons
- Reset switches
- LEDs and Ambient light sensor
12mm 12528 LDR 10- 20K
- Diameter: 12 mm
- No. of pins: 2
- Type of mounting: PCB Through Hole
- Maximum Operating Temperature: +70˚C (Approx.)
- Dark resistance: 1-20MΩ
- Spectral peak: 560nm
- Maximum voltage: 250 VDC
- Maximum wattage: 200 mW
- Light resistance (10 Lux): 10-20 KΩ
- Dark resistance: 2 MΩ
- Resistance illumination: 3
- Response time: 20ms (Rise), 30ms (Down)
NUCLEO-L433RC-P Development Board, STM32 Nucleo-64, STM32L433RC MCU, Arduino Uno & ST Morpho Connectivity
- Product: NUCLEO-L433RC-P Development Board
- Core Architecture: ARM
- Core Sub-Architecture: Cortex-M4
- Silicon Family Name: STM32L4
- Silicon Core Number: STM32L433RC
- Silicon Manufacturer: STMicroelectronics
Official 7Semi STM32G050F6P6 STM32 Mini Development Board
-
STM32G050F6P6 microcontroller delivering strong processing capability with up to 48KB flash memory and 6KB RAM
-
Compact, pocket-sized design with essential peripherals including GPIOs, timers, and ADC for connecting sensors and actuators
-
Easy powering and programming through the onboard USB Micro-B connector for a clean and simple setup
-
Beginner-friendly layout with accessible documentation, datasheets, and example code
-
Broad compatibility with the STM32 ecosystem for both hobbyist and professional applications
-
Operating frequency up to 72 MHz
-
32K flash memory and 20K SRAM
6Pin PL2303HXD USB to TTL/RS232
- Supports RS-232 serial interface with Programmable baud rate from 75 bps to 12 Mbps
- Compatible with the RS422/RS485 interface
- Extensive flow control mechanism like adjustable high/low watermark level, automatic hardware or software flow control, and inbound data buffer overflow detection.
-
The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB
- The TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTD’s FT232RQ USB to Serial
- Cables are FCC, CE, RoHS compliant and are available at TTL levels 3.3V
-
It is USB 2.0 full speed compatible. The USB side of the cable is USB powered.
Official NUCLEO-F410RB STM32F410 Nucleo-64 STM32F4 ARM Cortex-M4 MCU 32-Bit Embedded Evaluation Board
- USB VBUS or external source (3.3V, 5V, 7 to 12V) and power management access point
- USB communication (LD1), user LED (LD2), power LED (LD3)
- Two push buttons – USER and RESET
- USB re-enumeration capability – virtual com port, mass storage, debug port
- Supported by wide choice of IDEs including IAR, Keil, GCC-based IDEs
X-NUCLEO-IHM03A1 PowerSTEP01 STMicroelectronics Stepper Motor Driver for STM32 Nucleo Board
- Voltage range from 10.5 V to 85 V
- Phase current up to 10 A rms
- Power OK and fault LEDs
- Up to 1/128 micro-stepping
- Programmable speed profile and overcurrent protection
- Sensorless stall detection
- Adjustable output slew rate
- Overtemperature protection
- Compatible with Arduino UNO R3 connector
- Compatible with STM32 Nucleo boards
- Suitable for multi-motor solution
- RoHS compliant
Texas Instruments LAUNCHXL-RM42 Hercules RM42L432 LaunchPad Development Kit
- Microcontroller: RM42L432
- USB powered
- On board USB XDS100v2 JTAG debug
- On board SCI to PC serial communication
- Two LEDs
- Reset switches
- Ambient light sensor
2.2 inch LCD color screen TFT SPI serial interface 240*320 module compatible with 5110
- Display Size: 2.2″
- Driver IC: ILI9341
- Input Voltage (V): 3.3 to 5
- Pixel Resolution: 240×320
- Interface Type: SPI
- Easy to expand the experiment with SD card slot
Official xG26-DK2608A EFR32xG26 IoT Dev Kit Silicon Labs XG26 + 10 DBM DEV KIT (BRD2608A)
- Based on EFR32xG26 2.4 GHz Wireless SoC
- +10 dBm, 1536 kB flash, 256 kB RAM, 6×6 QFN48
- Secure Vault High
- AI/ML Hardware Accelerator
- Packet Trace Interface (PTI)
- Virtual COM Port
- On-board SEGGER J-link Debugger Supporting
- External Device Debugging
- User LED and Pushbuttons
- Si7021 RHT Sensor
- Intertial Sensor
- Stereo Microphones
- Pressure Sensor
- Ambient Light Sensor
- Hall-effect Sensor
- CR2032 Coin Cell Battery Support
SYB-500 Combined Breadboard Circuit Board (4-Piece combo sets)
- 700 tie-points for large projects
- Solderless design for easy use
- Durable construction for long-lasting use
- Color-coded terminals for easy identification
- Self-adhesive backing for secure mounting
- RoHS compliant for environmental safety
