Touch switch sensor module Double sided touch sensors TouchPad 4p/3p interface
- Input Supply voltage (VDC):3.3 ~ 5
- Working current (VCC=5V) (μA):18
- Length (mm):38.3
High Quality Full Amperes 12V 1A EU Plug Adapte0
- This is a durable product with a 6-month warranty.
- The adapter is easy to use.
- It comes with a long wire.
- Wide input voltage range (100VAC-270VAC).
- Very low no-load power consumption.
SG90 Continuous Rotation 360 Degree Servo Motor For Arduino Robotics RC Car DIY Projects
- Item Type: TowerPro Servo Motor
- Model Series: SG Series
- Rotation: 360Degree
- Torque Rating: 1.2kg-cm
- Model No: SG90
- Operating Voltage: 3.0 ~ 7.2VDC
- Operating Speed @4.8V: 0.12sec/60°
7Semi RJ45 Connector MagJack Ethernet Breakout
-
Official 7Semi RJ45 MagJack Ethernet Breakout Board
-
LPJ0011FBNL single-port RJ45 connector
-
Integrated 10/100 Base-T Ethernet magnetics
-
Pre-soldered RJ45 jack for quick setup
-
Built-in status LEDs and EMI shielding
-
All Ethernet pins broken out for easy access
-
Breadboard and prototype friendly design
-
Ideal for IoT, robotics, and industrial projects
5V Flame sensor module relay module fire alarm
- Operating Voltage (VDC)- 3.3 ~ 5
- Maximum Voltage(V)- 250V AC
- Maximum Operating Current (A)- 10
- Supply Current (A)- 150mA
- Operating Temperature (°C)- -40 to 80
- Opt. Relative Humidity(RH)- 20% ~ 85%
- Operating Distance Range (Meter)- 0.8
- Storage condition (℃)- – 65 to 125
5-Channel Flame Sensor Module
- Detecting range: >120 degree
- Analog and digital outputs
- On-board potentiometer and indicators
- 1% resistors to make this module more reliable and precise
- Operating Voltage: 3.3V – 9V
- Board Diameter: 40 mm.
ESP32 Development Board TYPE-C/Micro USB ESP32 Expansion Board 30pin Female header
- Item Type: Dev. Board
- Based On: ESP32 Based
- Compatibility: ESP32 Development Board, ESP32S Development Board
- Power Supply(V): DC 6.5-16v and USB 5V
- GVS output power supply: 5V or 3.3V
- No. of Pins: 30PIN
- Processor Count: 2
- Hardware Interface: USB Type-C / Micro USB
5V Photosensitive diode relay module
- Trigger Voltage: 5VDC
- Switching Voltage: 250VAC@10A; 30VDC@10A
- Photosensitive Relay Module
- Onboard Multiturn Potentiometer to Control Brightness Detection Value
PT100 Platinum Resister Temp Probe Temperature Sensor 2 wires/1 Meter
- Model number: FTARP05 series
- Mounting form Polish rod probe
- The Probe material: Stainless steel
- Probe diameter: 4mm
- Length of the probe: 30mm
- Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated)
- Accuracy ±(0.3°C+0.5%|t|)
- Thermal response time: <0.5s
Weighing Load Cell Sensor 1Kg for Electronic Kitchen Scale YZC-131 With Wires
- Weighing Range: 0 ~ 1 kg.
- Rated Output: 1.0 ± 0.1mV / V.
- Non Linear Output: ± 0.03% F.S.
- Input Impedance: 1066 ± 10% Ω.
- Output Impedance: 1000 ± 10% Ω.
- Insulation Resistance: 2000 MΩ.
ESP32 Development Board TYPE-C/Micro USB ESP32 Expansion Board 38PIN Female header
- Interface type: Standard 38Pin interface
- USB interface: 1
- TYPE-C interface: 1
- DC interface: 1
Pulse Sensor, Heart Rate Sensor
- A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required.
- The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything.
- Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting.
Official 7Semi UART Serial to RS485 Converter Breakout – MAX485
-
Powered by MAX485 RS485 transceiver
-
Reliable long-distance serial communication
-
High noise immunity with EMI reduction
-
Low power consumption design
-
Built-in thermal shutdown and short-circuit protection
-
Fail-safe receiver for stable data output
-
Ideal for industrial and embedded applications
MAX7219 8×8 LED Dot Matrix Module with cable (Red)
- Driver Chip: MAX7219
- Input Voltage: 4-5.5V
- Input Current 330mA
- Requires only 3 communication wires of MCU
- A single module can drive an 8 * 8 common cathode LED
- Connecting wires included
- Easy to interface with variety of MCU platforms
- SPI based control
Pressure Sensor Air Module Water Level Sensor Module,0-40KPa 3.3V-5V
- Pressure Range: 0 to 40 kPa
- Output Type: Analog voltage output
- Power Supply Voltage: Typically operates from 3.3V to 5V DC
Raindrops Detection Sensor Module with 5V Relay Module
- Relay Operating Voltage: 5VDC
- Relay load capacity: 250V 10A (AC) 30V 10A (DC)
- Sensor PCB Dimension: 55 x 40 mm
- The LM393, use of the wide voltage comparator
- Output LED indicator
- TTL Compatible
0.96 Inch 80*160 IPS TFT Module 8pin (with GND VCC) ST7735 Chip
- Product Type: TFT
- Resolution: 80*160
- Display Size: 0.96 Inch
- No.of Pins: 8
MPU-6050 3-Axis Accelerometer and Gyro Sensor
- Chip built-in 16bit AD converter, 16-bit data output
- Driver Chip: MPU6050
- Operating Voltage: 3-5V DC
- Communication: I2C/IIC Protocol
- Gyro Range: ± 250, 500, 1000, 2000 °/s
- Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
W25Q128 Storage Module 128Mbit Flash SPI Interface
- Using serial Nor flash external expansion memory chip W25Q128.
- Operating Voltage: 2.7-3.6V
- Support the SPI interface.
- Capacity: 128M-bit / 16M-byte
- Clock Frequency: ≤ 104MHz
TM1638 Button Digital LED Display Module
- Use TM1638 digital tube drive chip to drive a common cathode LED digital tube.
- Can be extended to 3 * 8 buttons, led digital tube and can be controlled separately.
- Support 8 brightness control, led digital tube and use the same brightness.
- Support cascading up to 6 of the same module.
- 8 LED, 8-bit digital tube and 8 buttons, common cathode LED digital tube, such as STC microcontroller can be directly connected.
