Official 7Semi INA169 60V 5A Analog DC Current Sensor Breakout
-
Based on Texas Instruments INA169 current-sense amplifier
-
Measures DC current up to 5A
-
Wide input voltage range: 2.7V to 60V
-
Analog output for easy ADC interfacing
-
Low offset voltage and low power consumption
-
Adjustable gain for flexible current sensing
-
Ideal for power monitoring and battery management
Official 7Semi DC Buck Converter Breakout 5V 2A Out (AP62301)
-
5V DC output with up to 2A continuous current
-
Wide input voltage range: 7V to 14V DC
-
AP62301 synchronous buck converter IC
-
Low EMI design for noise-sensitive applications
-
High efficiency with low output ripple
-
Compact 18 × 16 mm breakout board
-
Built-in protection: over-current & over-temperature
Official 7Semi DC Buck Converter Breakout 3.3V 2A Out (AP62301)
-
Fixed 3.3V DC Output
-
Up to 2A Continuous Output Current
-
Based on AP62301 Synchronous Buck Converter
-
Wide Input Voltage Range: 4.2V–14V
-
Low EMI Optimized Design
-
High Efficiency Step-Down Conversion
-
Low Output Ripple & Stable Regulation
-
Built-In Over-Current & Over-Temperature Protection
-
Soft-Start for Safe Power-Up
-
Ideal for IoT, Embedded & Battery-Powered Applications
Official 7Semi DC Buck Converter Breakout 3.8V 2A Out (AP62301)
-
Fixed 3.8V DC Output
-
Up to 2A Continuous Current
-
Based on AP62301 Synchronous Buck Converter
-
Wide Input Voltage: 4.2V–14V DC
-
High Efficiency Step-Down Regulation
-
Low EMI Optimized Design
-
High Switching Frequency up to 2.2MHz
-
Ultra-Compact 18 × 16 mm PCB
-
Stable Output for Battery-Powered Devices
-
Ideal for IoT & Embedded Applications
Official 7Semi INA219 3-Channel DC Current Sensor Breakout – 26V 3.2A Max
-
3-Channel DC Current, Voltage & Power Monitoring
-
Based on TI INA219 Sensor IC
-
High-Side Current Sensing Design
-
Bus Voltage Measurement up to 26V
-
I2C Interface for Easy Integration
-
Programmable Gain & Conversion Time
-
Internal Power & Current Calculation
-
Low Power Consumption
-
Compact Breakout Board
-
Ideal for Battery, Motor, IoT & Power Systems
Official 7Semi INA219 Voltage, Current, Power Monitor Sensor Breakout I2C
-
High-Side Voltage, Current & Power Monitoring
-
Bus Voltage Measurement: 0V–26V
-
Onboard Precision Shunt Resistor
-
I2C & SMBus Communication Interface
-
16 Programmable I2C Addresses
-
Internal Calibration & Power Calculation
-
Programmable Gain, Conversion Time & Filtering
-
Low Power Consumption (~1 mA Standby)
-
Compact Breakout Board Design
-
Compatible with Arduino, Raspberry Pi & ESP32
Official 7Semi-TCA9548A I2C Multiplexer Board – 8-Channel I2C Bus Switch
-
8-Channel I2C Multiplexer / Switch
-
Based on TI TCA9548APWR IC
-
Solves I2C Address Conflicts
-
Independently Controlled I2C Channels (SD0–SD7)
-
Software-Selectable Channel Control
-
Supports Multi-Master & Multi-Slave I2C
-
3.3V Logic Level Compatible
-
Low-Power, Compact PCB Design
-
Reset Pin for Reliable Operation
-
Ideal for Raspberry Pi, STM32, ESP32 & Robotics Applications
Official 7Semi ADS1115 16bit 4-Channel ADC Board with PGA I2C
-
16-Bit High-Resolution ADC
-
Texas Instruments ADS1115 IC
-
4 Analog Input Channels
-
Integrated Programmable Gain Amplifier (PGA)
-
I2C Interface for Easy Communication
-
Wide Supply Voltage: 2.0V–5.5V
-
Supports 3.3V & 5V Systems
-
Configurable Data Rate: 8–860 SPS
-
Low Power Consumption
-
Single-Ended & Differential Inputs
-
Compact Breakout Board Design
-
Compatible with Arduino, Raspberry Pi & ESP32
Official 7Semi ADS1263 32bit ADC with PGA Breakout
-
32-Bit High-Resolution ADC – Delivers ultra-precise measurements for high-accuracy sensing applications
-
Based on TI ADS1262 – Ensures low noise, low offset, and low drift performance
-
Integrated Programmable Gain Amplifier (PGA) – Allows direct connection of low-level sensor signals
-
Onboard Precision Voltage Reference – Improves measurement stability and repeatability
-
Wide Data Rate Support – Configurable from 2.5 SPS to 38,400 SPS for flexible performance tuning
-
Auxiliary 24-Bit Delta-Sigma ADC – Enables simultaneous background or diagnostic measurements
-
Single-Cycle Settling Digital Filter – Minimizes latency during channel switching
Official 7Semi 30V 10A Single Channel Motor Driver Vikram-3010
-
6V–30V Wide Voltage Support
-
10A Continuous Current Capacity
-
Single-Channel Brushed DC Motor Driver
-
Bi-Directional Forward & Reverse Control
-
3.3V & 5V Logic Level Compatible
-
PWM & DIR Control Interface
-
Fully NMOS H-Bridge for High Efficiency
-
No External Heat Sink Required
-
Onboard Test Buttons for Quick Checking
-
Motor Output Status LEDs
-
Overcurrent & Over-Temperature Protection
-
Undervoltage Shutdown Safety
-
Logic Input Range: 1.8V–12V
-
Compatible with Arduino, Raspberry Pi & PLCs
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Enables seamless UART to I2C protocol conversion
-
Supports UART baud rates up to 460.8 kbps
-
256-byte FIFO buffer for reliable data transfer
-
ASCII-based command interface for easy control
-
User-configurable GPIO pins for added flexibility
-
Ideal for embedded systems and industrial applications
7Semi RJ45 Connector MagJack Ethernet Breakout
-
Official 7Semi RJ45 MagJack Ethernet Breakout Board
-
LPJ0011FBNL single-port RJ45 connector
-
Integrated 10/100 Base-T Ethernet magnetics
-
Pre-soldered RJ45 jack for quick setup
-
Built-in status LEDs and EMI shielding
-
All Ethernet pins broken out for easy access
-
Breadboard and prototype friendly design
-
Ideal for IoT, robotics, and industrial projects
Official 7Semi EC200U-CN LTE 4G GNSS Ultra-compact Nano Modem
-
Official 7Semis 4G LTE USB Nano Modem
-
Powered by Quectel EC200U-CN LTE Cat-1 module
-
Supports LTE-FDD, LTE-TDD, and GSM/GPRS networks
-
Plug-and-play USB connectivity for PC and laptop
-
Ultra-compact size for space-constrained designs
-
Ideal for IoT, M2M, tracking, and industrial applications
-
Includes wide-band 4G LTE antenna (700–2700 MHz)
-
IPEX (u.FL) connector with 3M adhesive mounting
SMA Adapter SMA Jack to SMA Jack Straight (SMA Female to SMA Female Adapter)
- SMA Female to SMA Female RF Connector
- Type: Female to Female
- Color: Gold Tone
- Max Frequency:18 GHz
16GB Micro SD Card, Class 10 (China Quality)
-
16GB storage capacity
-
Class 10 high-speed performance
-
Compatible with microSD-supported devices
-
Durable and reliable design
-
Suitable for photos, videos, and files
Official 7Semi BME690 Digital Sensor Probe – Metal (Temperature, Humidity, Pressure, Gas | I2C)
- Measures temperature, humidity, pressure, and gas (VOC/VSC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports Bosch BSEC software for advanced air-quality processing
-
I²C digital interface for easy integration
-
3.3 V operating voltage
-
Low-power design for embedded and IoT applications
-
Compact, rugged, and plug-and-play probe construction
-
Ideal for air-quality, HVAC, and environmental monitoring
Official 7Semi BME690 Digital Sensor Module – Temperature, Humidity, Pressure, Gas | I2C/SPI
-
Official 7Semi BME690 digital environmental sensor module
-
Measures temperature, humidity, pressure, and gas (VOC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports I2C and SPI communication interfaces
-
Wide operating voltage 3.3V to 5V
-
Compact and low-power design
-
Easy integration with Arduino, ESP32, Raspberry Pi, STM32
-
Ideal for IoT, air-quality monitoring, and smart systems
Official BME690 Digital Sensor Nano Breakout 2.54mm – Temperature, Humidity, Pressure, Gas | I2C
-
Measures temperature, humidity, pressure, and gas (VOC/VSC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports Bosch BSEC software for advanced air-quality processing
-
I²C interface for easy microcontroller integration
-
3.3 V operating voltage
-
Low-power design for battery-powered applications
-
Standard 2.54 mm pin pitch for breadboard compatibility
-
Compact and rugged breakout design
-
Ideal for IoT, smart home, HVAC, and air-quality monitoring
Official 7Semi DS18B20 Digital Waterproof Temperature Sensor Probe 3M Cable
-
7Semi DS18B20 digital waterproof temperature sensor probe
-
3-meter insulated cable for flexible installation
-
Measures temperature from −55°C to +125°C
-
±0.5°C accuracy for precise monitoring
-
1-Wire digital interface for easy integration
-
Compatible with Arduino, Raspberry Pi, ESP8266, ESP32
-
Stainless steel probe for durability and corrosion resistance
-
Suitable for liquids, outdoor, HVAC, and industrial use
Official 7Semi PT100 RTD 3-Wire Temperature Sensor Amplifier Breakout Board – MAX31865
-
Official 7Semi MAX31865 RTD amplifier breakout board
-
Supports PT100 and PT1000 temperature sensors
-
Optimized for 3-wire RTD configuration
-
Compatible with 2-wire and 4-wire RTD sensors
-
High-accuracy RTD-to-digital conversion
-
SPI interface for easy microcontroller integration
-
Built-in fault detection for open and short circuits
-
Compact and reliable design for industrial use
