NUCLEO-G491RE Development Board, STM32 Nucleo-64, STM32G491RE MCU, Arduino Uno & ST Morpho Connectivity
- Product: NUCLEO-G491RE Development Board
- Core Architecture: ARM
- Core Sub-Architecture: Cortex-M4
- Silicon Family Name: STM32
- Silicon Core Number: STM32G491RET6U
MQ-5 liquefied gas Methane Gas Sensor Module
- Model: MQ-5
- Operating Voltage: 5V DC
- Operating Temparature:-20~40 degree celcius
5V 3A Adapter Charger EU Plug
- Input Voltage (V): 100 ~ 270 VAC @50 ~ 60Hz.
- Input current (mA): 100.
- Output Power: 5V 3A.
- Load regulation (%): ±5.
- Input Plug: 2-Pin EU type.
- Output Plug: DC Jack 5.5mm.
NEO-6M GPS Module with EEPROM for Aero Quad with Antenna for Flight Control GY-NEO6MV2 （with Battery）
- 5Hz position update rate
- Operating temperature range: -40 TO 85°CUART TTL socket
- EEPROM to save configuration settings
- Rechargeable battery for Backup
- The cold start time of 38 s and Hot start time of 1 s
- Supply voltage: 3.3 V
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
- SuperSense ® Indoor GPS: -162 dBm tracking sensitivity
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
- Separated 18X18mm GPS antenna
Official 7Semi INA219 3-Channel DC Current Sensor Breakout – 26V 3.2A Max
-
3-Channel DC Current, Voltage & Power Monitoring
-
Based on TI INA219 Sensor IC
-
High-Side Current Sensing Design
-
Bus Voltage Measurement up to 26V
-
I2C Interface for Easy Integration
-
Programmable Gain & Conversion Time
-
Internal Power & Current Calculation
-
Low Power Consumption
-
Compact Breakout Board
-
Ideal for Battery, Motor, IoT & Power Systems
Official 7Semi PT100 RTD 3-Wire Temperature Sensor Amplifier Breakout Board – MAX31865
-
Official 7Semi MAX31865 RTD amplifier breakout board
-
Supports PT100 and PT1000 temperature sensors
-
Optimized for 3-wire RTD configuration
-
Compatible with 2-wire and 4-wire RTD sensors
-
High-accuracy RTD-to-digital conversion
-
SPI interface for easy microcontroller integration
-
Built-in fault detection for open and short circuits
-
Compact and reliable design for industrial use
NUCLEO-G070RB Development Board, STM32 Nucleo-64, STM32G070RB MCU, Arduino Uno & ST-Link Debugger
- STM32 microcontroller in LQFP64 package
- External SMPS to generate Vcore logic supply (only available on ‘-P’ suffixed boards)
- 1 user LED shared with Arduino™
- 1 user and 1 reset push-buttons
TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino
- 4-digit 7-segment LED display showing numbers (0-9) and some letters (A, B, C, etc.).
- Managed by TM1637 driver chip for simplified interfacing.
- Uses I2C protocol with only two wires (SDA and SCL) to connect to the microcontroller.
- Compact design with 0.36-inch digit height per segment.
1.3 Inch SPI 6-Pin OLED Display Module (BLUE)
- Size: 1.3 inch
- Resolution: 128 x 64
- Controlling Driver Chip: SSH1106
- Display Area: 21.74 x 10.86mm
- Driving Voltage: 3.3-5V
- Operating Temperature: -40~70 Celsius
- Interface Type: SPI
- Light Color: BLUE
- Number of pins: 6
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Enables seamless UART to I2C protocol conversion
-
Supports UART baud rates up to 460.8 kbps
-
256-byte FIFO buffer for reliable data transfer
-
ASCII-based command interface for easy control
-
User-configurable GPIO pins for added flexibility
-
Ideal for embedded systems and industrial applications
Official Silicon Labs XG22-EK2710A EFR32MG22E Explorer Kit (BRD2710A)
- Based on EFR32MG22E224F512IM40 2.4 GHz Wireless SoC
- +6 dBm, 512 kB Flash, 32 kB RAM, QFN48
- Two LEDs and two push buttons
- Reset button
- USB connector for power and debug connection
- On-board SEGGER J-Link debugger
- Virtual COM port
- Packet Trace Interface (PTI)
- Breakout pads for GPIO access and connection to external hardware
- Third-party add-on connectors
- mikroBUS™ socket
- Qwiic® connector
Official Texas Instruments LP-MSPM0L1117 LaunchPad™ Development Kit for 32MHz Arm® Cortex®-M0+ MCU
-
Based on MSPM0L1117 Arm® Cortex-M0+ MCU
-
Compact, low-cost evaluation module (EVM)
-
On-board debug probe for programming, debugging & energy measurement
-
Includes 2 push buttons and 2 user LEDs for quick testing
-
Access to 40+ GPIO pins for external interfacing
-
Supports ADC inputs with low-pass filter placeholders for analog accuracy
-
Optimized for low-power and IoT applications
-
Fully supported by TI MSPM0 software ecosystem (Code Composer Studio™, drivers, libraries, examples)
-
Suitable for students, hobbyists, and professional developers
-
Ideal for IoT devices, automation, consumer electronics, and embedded projects
MQ-8 hydrogen Gas Sensor Module H2 Alarm Detection
- Using high-quality dual-panel design, with power indicator and TTL signal output instructions.
- The switching signal having a DO (TTL) output and analog output AO.
- TTL output valid signal is low.
- The higher the voltage, the concentration of the analog output voltage is higher.
- A hydrogen gas detection with good sensitivity.
- Has a long life and reliable stability
GY-61 ADXL335 3-axis accelerometer tilt angle module
- Supply Voltage (V): 3 to 6
- Each Axis Bandwidth: 50Hz
- Operating Temperature (°C): -40 to +90
- Length (mm): 21
- Width (mm): 16
- Height (mm): 2.5
- Weight (gm): 0.6
HC-06 6pin Bluetooth Module Without Button
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
Official 7Semi L89 USB Dongle Multi-GNSS Engine for GPS, IRNSS, GLONASS, BeiDou, Galileo and QZSS
-
GNSS Bands: GPS L1 (1575.42 MHz), Galileo E1, IRNSS L5 (1176.45 MHz), GLONASS L1, BeiDou B1
-
Multi-GNSS: GPS, Galileo, GLONASS, BeiDou, IRNSS (NavIC), QZSS
-
Position Accuracy: < 1.8 m (CEP)
-
Velocity Accuracy: < 0.1 m/s
-
Acceleration Accuracy: < 0.1 m/s²
-
Timing Accuracy: 1PPS, 3.9 ns RMS
-
Sensitivity: Acquisition –147 dBm, Tracking –163 dBm
-
Operating Temperature: –40 °C to +85 °C
-
Dimensions: 62.82 mm × 19.06 mm
NRF24L01+PA+LNA Wireless Transceiver Module with Antenna (2.4GHz – 1100 Meters)
- Voltage: 3-3.6V
- Max output power: +20 dBm
- Working current in transmit mode: 115mA
- Working current in receiver mode: 45mA
- Current in mode: 4.2uA
- Operating temperature: -20-70 degree
- Operating frequency: 2.4GHz ~ 2.5GHz
- Communication distance: Maximum 1100 meters
Robot Smart Car Chassis-Black
- Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY.
- With a 4 AA battery box (batteries not included).
- It can be used for distance measurement, velocity.
- Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing,
Super UNO R3 Starter Kit(with Tutorial+with Logo+without Battery+Plastic Box）
- Comes with a detailed and user-friendly tutorial: Free PDF tutorial with more than 22 lessons available for download
- A great way for the beginners to get started with Arduino programming
- All modules are ready to use, no soldering needed
SPI to Ethernet Hardware TCP/IP W5500 Ethernet Network Module
- Supports 8 independent sockets simultaneously.
- Internal 32Kbytes Memory for Tx/Rx Buffers.
- Power off mode: support.
- Network wake: support.
- Factory and Building Automation
- Medical Monitoring Equipment
