3.5 inch TFT Shield LCD Module 480×320 for Arduino Uno with Touch(Parallel Interface)
-
3.5-inch TFT LCD screen size
-
480 × 320 pixel resolution
-
65K RGB color display
-
ILI9486 display driver IC
-
8-bit parallel interface
-
Resistive touch panel support
-
On-board micro-SD card slot for media loading
-
Compatible with both 5V and 3.3V logic levels
Ethernet W5100 Shield Network Expansion Board with Micro SD Card Slot for Arduino
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by for Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Can be accessed using the Mini SD TF library.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
0.96 Inch I2C/IIC 4-Pin OLED Display Module (WHITE)
- Size: 0.96 inch
- Resolution: 128 x 64
- Controlling Chip: SSD1306
- Display Area: 21.74 x 10.86mm
- Driving Voltage: 3.3-5V
- Operating Temperature: -40~70 celsius
- Interface Type: IIC
- Light Color: White
LM2596S DC-DC Buck Converter Step Down Module – Variable Voltage (3A BUCK 3-40V TO 1.5-35V)
- Input Voltage(VDC): 4 ~ 40.
- Output Voltage(VDC): 1.3 ~ 37.
- Output Current: 2A Rated, ( 3A maximum with heat sink).
- Switching Frequency: 150 kHz.
- Input reverse polarity protection.
- Built-in output short protection function.
Acrylic Bracket For HC-SR501
- Material: Acrylic
- Dimensions: 50 x 40 x 18 (LxWxH) mm.
- Weight: 8 gm
Official 7Semi-TCA9548A I2C Multiplexer Board – 8-Channel I2C Bus Switch
-
8-Channel I2C Multiplexer / Switch
-
Based on TI TCA9548APWR IC
-
Solves I2C Address Conflicts
-
Independently Controlled I2C Channels (SD0–SD7)
-
Software-Selectable Channel Control
-
Supports Multi-Master & Multi-Slave I2C
-
3.3V Logic Level Compatible
-
Low-Power, Compact PCB Design
-
Reset Pin for Reliable Operation
-
Ideal for Raspberry Pi, STM32, ESP32 & Robotics Applications
Official 7Semi INA219 Voltage, Current, Power Monitor Sensor Breakout I2C
-
High-Side Voltage, Current & Power Monitoring
-
Bus Voltage Measurement: 0V–26V
-
Onboard Precision Shunt Resistor
-
I2C & SMBus Communication Interface
-
16 Programmable I2C Addresses
-
Internal Calibration & Power Calculation
-
Programmable Gain, Conversion Time & Filtering
-
Low Power Consumption (~1 mA Standby)
-
Compact Breakout Board Design
-
Compatible with Arduino, Raspberry Pi & ESP32
HX711 Weighing Pressure Sensor Module Big Size
- Output Sensitivity: 1.0 ± 0.1 mV / V.
- Two selectable differential input channels.
- On-chip active low noise PGA with the selectable gain of 32, 64 and 128.
- On-chip oscillator requiring no external component with optional external crystal.
- On-chip power-on-reset.
- Measurement Resolution: 24 bit.
USB 2.0 A-A Male Cable 0.3m
- Color : Blue
- Length (cm) : 30
- USB Type : Type-A to Type-B
- Weight (gm) : 20
WEMOS SHT30 I2C Digital Temperature and Humidity Sensor module
- I2C Interface
- Two user selectable addresses
- Typical accuracy ±3%RH and ±0.3°C
LCD1602 Blue Backlight 5V (AIP31066 Chip)
- Display Contents: 16 * 2 Characters (5*8 dots ) (16 characters per line, 2 lines).
- Shows white characters on a blue background.
- Equipped with a backlight for enhanced visibility in low-light conditions.
- Driver IC: AIP31066
- Interface: Parallel
- Operating Temperature: -20 C-﹢70 C
- Storage Temperature: -30 C-﹢80 C
9 in 1 Gas Sensor kit
- Power supply: from 2.5 V to 5 V
- Analog and digital output
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
Official 7Semi ST-LINK/V2, ST-LINK/V2.1 Debugger Programmer USB, Original STM Chip
MAX485 TTL to RS485 Converter Module
- On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
- A low power consumption for the RS-485 communication
- Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
- Slew-rate limited transceiver
- All pins of the chip have been lead to can be controlled through the microcontroller.
- Convenient RS-485 communication wiring
- Multiple Units can be connected to the same RS-485 bus wiring.
- All Chip pins are brought out for proper controls
Raindrops Detection Sensor Module with 12V Relay Module
- Relay Operating Voltage: 12VDC
- Relay load capacity: 250V 10A (AC) 30V 10A (DC)
- Sensor PCB Dimension: 55 x 40 mm
- The LM393, use of the wide voltage comparator
- Output LED indicator
- TTL Compatible
LM35D Analog Temperature Sensor Module + Cable
- Based on the semiconductor LM35 temperature sensor
- Can be used to detect ambient air temperature
- Calibrated directly in °Celsius (Centigrade)
- Linear + 10 mV/°C Scale Factor
- 0.5°C Ensure accuracy (at +25°C)
- Low power consumption, less than 60uA
- Low output impedance, 1mA current through only 0.1Ω
- With screw holes for easy installation and fixed. Aperture 2.6mm
3.5mm 3pin Straight Pin Screw Terminal Block
- Pitch: 3.5 mm
- Poles: 3 Pin
- Rated voltage: 300 V
- Rated current: 10 A
- Withstand length: 4.5~5 mm
- Withstanding voltage: AC 1500V/1Min
315MHz RF Wireless Transmitter and Receiver Kit
- Operating voltage: 5V.
- Quiescent Current: 4mA.
- Receiving frequency: 315MHz.
- Receiver sensitivity: -105 dB.
- Communication Distance (m): 20 ~ 200 meter.
- RF Transmitter Receiver Module 315MHz Wireless Link Kit For Arduino
Raspberry Pi Pico Basic Starter Kit (Tutorial, Small Plastic Retail Box)
- This basic beginner kit with all the necessary components to jumpstart your interest in learning and making your projects.
- Supports MicroPython C and C++ Programming Language
- A great way for beginners to get started with Pure Electronics.
- All components are ready to use, no soldering is needed.
- Different Sensor modules in a kit
- All modules are packed in protective plastic bags
Correlation Photoelectric Infrared Count Slot Sensor 10mm
- The width of the optical coupling slot: 19mm
- Single signal output.
- The circuit board output switch!
- The output valid signal is low.
- Can be used for workpiece counts.
- It can also be used for industry counting, motor speed testing.
