Official 7Semi UART Serial to RS485 Converter Breakout – MAX485
-
Powered by MAX485 RS485 transceiver
-
Reliable long-distance serial communication
-
High noise immunity with EMI reduction
-
Low power consumption design
-
Built-in thermal shutdown and short-circuit protection
-
Fail-safe receiver for stable data output
-
Ideal for industrial and embedded applications
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Official 7Semi SC18IM704 UART to I2C Bus Bridge Breakout
-
Enables seamless UART to I2C protocol conversion
-
Supports UART baud rates up to 460.8 kbps
-
256-byte FIFO buffer for reliable data transfer
-
ASCII-based command interface for easy control
-
User-configurable GPIO pins for added flexibility
-
Ideal for embedded systems and industrial applications
Official 7Semi UART Mux Demux Breakout Board – 4 Channel (SN74LV4052)
-
Official 7Semi UART Mux Demux Breakout Board
-
Based on SN74LV4052 dual 4-channel multiplexer
-
Switch multiple UART devices using one UART port
-
Wide operating voltage range 1.65V – 5.5V
-
Supports both analog and digital signals
-
Low power and fast switching performance
-
Breadboard-friendly and easy to integrate
-
Ideal for IoT, robotics, and embedded systems
7Semi RJ45 Connector MagJack Ethernet Breakout
-
Official 7Semi RJ45 MagJack Ethernet Breakout Board
-
LPJ0011FBNL single-port RJ45 connector
-
Integrated 10/100 Base-T Ethernet magnetics
-
Pre-soldered RJ45 jack for quick setup
-
Built-in status LEDs and EMI shielding
-
All Ethernet pins broken out for easy access
-
Breadboard and prototype friendly design
-
Ideal for IoT, robotics, and industrial projects
Official 7Semi CH340C USB-C to Serial TTL Converter Breakout
-
Official 7Semi CH340C USB-C to Serial TTL converter
-
Powered by CH340C USB-to-UART chip
-
Modern USB Type-C connector
-
Supports RX, TX, DTR, CTS, VCC, and GND pins
-
TX (Blue) and RX (Red) activity LEDs
-
Ideal for Arduino, ESP32, ESP8266, GPS modules
-
Compact, reliable, and easy to use
-
Perfect for programming and debugging projects
Official 7Semi EC200U-CN LTE 4G GNSS Ultra-compact Nano Modem
-
Official 7Semis 4G LTE USB Nano Modem
-
Powered by Quectel EC200U-CN LTE Cat-1 module
-
Supports LTE-FDD, LTE-TDD, and GSM/GPRS networks
-
Plug-and-play USB connectivity for PC and laptop
-
Ultra-compact size for space-constrained designs
-
Ideal for IoT, M2M, tracking, and industrial applications
-
Includes wide-band 4G LTE antenna (700–2700 MHz)
-
IPEX (u.FL) connector with 3M adhesive mounting
SMA Adapter SMA Jack to SMA Jack Straight (SMA Female to SMA Female Adapter)
- SMA Female to SMA Female RF Connector
- Type: Female to Female
- Color: Gold Tone
- Max Frequency:18 GHz
16GB Micro SD Card, Class 10 (China Quality)
-
16GB storage capacity
-
Class 10 high-speed performance
-
Compatible with microSD-supported devices
-
Durable and reliable design
-
Suitable for photos, videos, and files
3.5 inch TFT Shield LCD Module 480×320 for Arduino Uno with Touch(Parallel Interface)
-
3.5-inch TFT LCD screen size
-
480 × 320 pixel resolution
-
65K RGB color display
-
ILI9486 display driver IC
-
8-bit parallel interface
-
Resistive touch panel support
-
On-board micro-SD card slot for media loading
-
Compatible with both 5V and 3.3V logic levels
Official 7Semi BME690 Digital Sensor Probe – Metal (Temperature, Humidity, Pressure, Gas | I2C)
- Measures temperature, humidity, pressure, and gas (VOC/VSC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports Bosch BSEC software for advanced air-quality processing
-
I²C digital interface for easy integration
-
3.3 V operating voltage
-
Low-power design for embedded and IoT applications
-
Compact, rugged, and plug-and-play probe construction
-
Ideal for air-quality, HVAC, and environmental monitoring
Official 7Semi BME690 Digital Sensor Module – Temperature, Humidity, Pressure, Gas | I2C/SPI
-
Official 7Semi BME690 digital environmental sensor module
-
Measures temperature, humidity, pressure, and gas (VOC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports I2C and SPI communication interfaces
-
Wide operating voltage 3.3V to 5V
-
Compact and low-power design
-
Easy integration with Arduino, ESP32, Raspberry Pi, STM32
-
Ideal for IoT, air-quality monitoring, and smart systems
Official BME690 Digital Sensor Nano Breakout 2.54mm – Temperature, Humidity, Pressure, Gas | I2C
-
Measures temperature, humidity, pressure, and gas (VOC/VSC)
-
Powered by Bosch Sensortec BME690 sensor
-
Supports Bosch BSEC software for advanced air-quality processing
-
I²C interface for easy microcontroller integration
-
3.3 V operating voltage
-
Low-power design for battery-powered applications
-
Standard 2.54 mm pin pitch for breadboard compatibility
-
Compact and rugged breakout design
-
Ideal for IoT, smart home, HVAC, and air-quality monitoring
Official 7Semi DS18B20 Digital Waterproof Temperature Sensor Probe 3M Cable
-
7Semi DS18B20 digital waterproof temperature sensor probe
-
3-meter insulated cable for flexible installation
-
Measures temperature from −55°C to +125°C
-
±0.5°C accuracy for precise monitoring
-
1-Wire digital interface for easy integration
-
Compatible with Arduino, Raspberry Pi, ESP8266, ESP32
-
Stainless steel probe for durability and corrosion resistance
-
Suitable for liquids, outdoor, HVAC, and industrial use
Official 7Semi PT100 RTD 3-Wire Temperature Sensor Amplifier Breakout Board – MAX31865
-
Official 7Semi MAX31865 RTD amplifier breakout board
-
Supports PT100 and PT1000 temperature sensors
-
Optimized for 3-wire RTD configuration
-
Compatible with 2-wire and 4-wire RTD sensors
-
High-accuracy RTD-to-digital conversion
-
SPI interface for easy microcontroller integration
-
Built-in fault detection for open and short circuits
-
Compact and reliable design for industrial use
Official 7SEMI PT100 RTD Temperature Sensor Probe 3-wire 1m -70~300C
-
High-precision PT100 RTD temperature sensor probe
-
Wide temperature measurement range from −70°C to +300°C
-
Uses premium JUMO platinum RTD chip for reliable accuracy
-
3-wire configuration for improved measurement stability
-
Complies with IEC 60751 Class A / F0.15 standards
-
Stainless steel probe with waterproof construction
-
2-inch probe length with 1-meter durable cable
-
Suitable for industrial, laboratory, HVAC, and process control applications
-
Designed for long-term stability and harsh environments
-
Ideal for professional and precision temperature monitoring
Official 7Semi NEO-M9N GPS Breakout, Precision GNSS Positioning
-
High-precision multi-GNSS GPS breakout module
-
Supports GPS, GLONASS, Galileo, and BeiDou
-
Fast position update rate up to 25 Hz
-
3.3V operating voltage
-
I2C and UART communication interfaces
-
Low power consumption for battery-powered projects
-
Compact design for space-constrained applications
-
Ideal for drones, robotics, navigation, and IoT tracking
Official 7Semi VL53L1X ToF Distance Sensor Breakout – 4 Meter
- VL53L1X Time-of-Flight (ToF) sensor breakout for distance measurement.
- High-Precision Ranging – Measures distances up to 4 meters with ±5% accuracy and 1mm resolution.
- Fast Response – Supports measurement frequencies up to 50 Hz for real-time applications.
- I²C Communication – Simple digital interface for integration with microcontrollers and embedded systems.
- Compact & Reliable – Small breakout design with stable operation under varying lighting conditions.
- Wide Applications – Ideal for robotics, drones, autonomous navigation, smart sensing, and IoT devices.
Official 7Semi SCD41 High Accuracy CO2, Temperature and Humidity Sensor Breakout I2C
- Photoacoustic CO2 sensor technology
- Integrated temperature and humidity sensor
- Measurement range: 400 ppm – 5000 ppm
- Accuracy: +-(50 ppm + 5 % of reading)
- Current consumption: 17 mA (meas. rate = 5 s) / 0.5 mA (meas. rate = 5 min)
- Fully calibrated and linearized
- I2C digital interface
Official 7Semi SCD40 CO2, Temperature and Humidity Sensor Breakout I2C
- Photoacoustic CO2 sensor technology (carbon dioxide sensor)
- Integrated temperature and humidity sensor
- Measurement range: 400 ppm – 2000 ppm
- Accuracy: +-(50 ppm + 5 % of reading)
- Current consumption: 17 mA (meas. rate = 5 s) / 0.5 mA (meas. rate = 5 min)
- Fully calibrated and linearized
- I2C digital interface
Official 7Semi SHT45 Digital Humidity and Temperature Sensor Probe 0.1C Accuracy 1% RH 16bit I2C
- Digital output, I2C interface (I2C address 0x44)
- Fully functional in condensing environment
- Variable power heater
- NIST traceability
- Breatable shell
- Corrosion resistance
- High temperature resistance
- Large air permeability, fast gas humidity flow and exchange rate, uniform divergence.
- Excellent ability of anti-dust, anti-corrosion and waterproof (IP65）
